? So, what next? Does anyone know of a reliable source to find the rebuild kit for the Mtd carb (951-05118B). I find it best to try to start the snowblower without priming it first. Priming your engine moves fuel from the fuel lines into the carburetor. So, I want to redo the rebuild, but as I said, I have not been able to find a carb rebuild kit for the Mtd 951-05118B. Fix: Replace your fuel filter if it is very dirty, gas is not able to flow through the filter, or you have fuel leaking from your fuel filter. I didn't remove the plastic metering plug. © 2023 Google LLC Struggling to start your snow blower this winter Dont worry, weve got you covered In this video, well show you exactly where to spray start fluid to get. Yeah, still "no joy" I did skip/miss one step. There is no port I could squirt the starting fluid in-at least, I dont think there is. If I start it up, then shut it off, then try to start it up again, it wont, until I squirt more starting fluid in. I suspect the answer is No, because I tried that, but the thing still won't start!!! :sad2: I drained the old gas, removed the carb, disassembled, cleaned, and reassembled, and filled with fresh gas. (Got it from a snowblower shop 10 years ago, and that guy died last year, and shop is closed now.) Yeah, it has a primer bulb on it. So, that's question 1 then, can you clean and rebuild a snowblower carb without using new parts? However, my searches and video watching gave me the impression that I should be able to disassemble, clean the carb and reassemble. I have searched for videos on tricks for carb problems and didn't find much of anything except that I need to rebuild the carb.Īfter digging online, it appears my engine is a 375-Qu and the carburetor itself is an Mtd 951-05118B.Īfter more searching online, I have not been able to find a rebuild kit for the Mtd 951-05118B. The engine’s carburetor won’t get any gas if the fuel filter is clogged. The engine may start right up with fresh fuel. In a well-ventilated area, drain the old gas out of the tank and fill it up with fresh gas. Primary troubleshooting steps taken so far:ġ) Checked snowblower for spark - checked good since it does turn over if you put gas into the cylinder.īased on the above, I am thinking it has to be the carburetor or possibly the primer button. Bad gasoline is one of the leading causes of snowblower starting problems. Now it won't start at all any and all help/advice will be greatly appreciated!! This can be your 1st step to troubleshooting your lawn mo. Starter fluid has helped me start my chainsaws, lawnmowers, high pressure water sprayer even one of my older outboard engines. This is a 1 minute video that shows you how to use the starting fluid on your gas or diesel engine. I have a can of it on my garage shelf to use when needed. It has been used once, but was not stored properly over the summer. Starter fluid Heck, I have successfully used that stuff for years, just be careful to avoid an enclosed area, best it used while the machine is outdoors. I think I have the bowl back on and not leaking now, but it still won't run without starter fluid.I have a Craftsman 247.883940 that I bought back in 2015. I should have just used the drain on the bowl because when I put the bowl back on, fuel was leaking :-( Do I have to replace a gasket since I took this off? Leaked a lot when I tilted the snowblower back. Then removed the carb bowl and got continuous flow of gas down my arm, until I found pushing float up stopped flow. finally got it to fire, but only stays running with repeated starter fluid sprays :-( It is firing at least. Found the throat / plastic channel to the carb intake down inside and after getting new can of starter fluid. Take all safety precautions provided in the. Remove the spark plug before performing any repairs. Got the cover off the thing finally and drained the fuel at bottom of tank. A Briggs & Stratton snowblower won’t start when there is a lack of fuel, air, or spark due to an empty fuel tank, old gasoline, bad spark plug, clogged fuel line, dirty carburetor, faulty starter, bad fuel cap or incorrect starting procedures. So we have had a mild winter / no snow but finally took advantage of the 65 degree weather and tried to work on the snowblower again.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |